![]() I didn't find any more detailed description of installation in Windows. When I intalled the stlink, I downloaded the stlink-1.3.0-win64.zip file, unzipped it to the c:/opt/stlink directory and set PATH to its bin directory. Please if you open the device manager, can you see the driver for the connected ST-Link programmer? And what you have on the related tab Driver in the first line (intermediary)? I have now libusb-win32 there. If i right click it and follow Properties/Driver/Driver. In the 'Device manager' it is located under Disk drives/STM32. But this micro controller is recognized as a 'USB mass storage device'. But it give me the message in the device manager 48 and the st-info -probe didn't find the programmer. This board has an integrated 'ST-Link V2' programmer / debugger based on the 'STM32F103C8' micro controller which actually communicates with the PC. Then I removed all stlink drivers and tried to install only the libusb-win32 driver. The tutorial 2 uses Flash Loader Demo and this older tutorial. When in DFU mode, I can see it as Universal Serial Bus Device/STM32 BOOTLOADER on Device Manager. My PC identifies it as mass storage and portable devices on Windows 10 Pro. Then I tried to install the libusb-win32 driver, after it the st-info -probe gave detailed output but with zero values and st-flash read. I found this question 1 where Device Manager reads the STM as Disk drives/STM32. or st-info -probe gave some errors and it didn't worked. Hello, I have been trying various methods of installing the ST-Link USB drivers on my Windows 11 Laptop, with absolutely no success. Then I had received a Blue Pill with STM32F103C8T6 and I connected it to the programmer. But I had no HW for connecting to programmer and I also thought, that the program response should be longer. ![]() Then the st-info -probe gave exactly the same short prompt as in your case. Because there was an uninstalled device STM32 ST-Link in the device manager, I tried to install the ST STM32 ST-LINK UTILITY, which installed also ST native driver. Have also installed the ST-LINK utility V4.1 in an attempt to connect to the ST-LINK/V2 device but it reports that it is unable to connect (as to be expected since the USB devcie driver is not working).The my posted program response it had reported immediately after the stlink installation. Starting from Windows ® 10, the STSW-STM32102 driver is no more adequate and the usage of the native inbox driver is recommended. Just wanted to verify that the ST-LINK/V2 will work with a USB3 port?Īlso I have a Silicon Labs device driver installed for a USB connection that I make to a Digilent Zybo board using Vivado and wondered if this could be conflicting with the functionality of the ST device driver? ![]() The driver install appeared to execute normally, and Device Manager now shows a USB device with name STM32 STLink, reporting 'This device is working properly. As far as I remember in the past this should show as an ST labelled device (cannot remember the exact naming). When the ST-Link v2 was plugged in it didnt show up in Device Manager, so I went to st.com and downloaded the driver package stsw-link009. It provides an easy-to-use and efficient environment for reading, writing and verifying device memory through both the debug interface (JTAG and SWD) and the bootloader interface (UART, USB DFU, I 2 C, SPI, and CAN). WinUSB CoInstallers for 32-bit and 64-bit versions of Windows ® 7, 8 and 10. In device manager, under Universal Serial Bus Controllers, I see a device that is marked as Unknown USB Device (Device Descriptor Request Failed). STM32CubeProgrammer (STM32CubeProg) is an all-in-one multi-OS software tool for programming STM32 products. STSW-LINK009 - ST-LINK, ST-LINK/V2, ST-LINK/V2-1, STLINK-V3 USB driver signed for Windows7, Windows8, Windows10, STSW-LINK009, STMicroelectronics. The last device you connected to this computer malfunctioned. In the meantime, to test the interface, I attached an ST-LINK/V2 device to a USB port and Windows displays the following message. I am intending to work with the NUCLEO-L476RG board which I will have shortly. Description STSW-LINK007 is the firmware upgrade application for ST-LINK, ST-LINK/V2, ST-LINK/V2-1, and STLINK-V3 boards through the USB port. ![]() I have installed SW4STM32 V2.2 onto a Windows 10 64bit PC including the drivers required for the ST-LINK debugging and programming interface.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |